Tenemos un Primario de 32 canales(bueno 30) e instalaremos una tarjeta sangoma A101D que es una tarjeta T1/E1 con cancelación de ECO incorporado.
[root@pbx ~]# wancfg_dahdi
would you like to generate
/etc/asterisk/chan_dahdi.conf
1. YES
2. NO
[1-2]:1
Configuring port 1 on A101 slot:4
bus:4.
-----------------------------------------------------------
Select media type for AFT-A101 on port 1 [slot:4
bus:4 span:1]
1. T1
2. E1
3. Unused
4. Exit
[1-4]:2
Configuring port 1 on 101 as E1, line
coding:HDB3, framing:CRC4
1. YES - Keep these settings
2. NO - Configure line coding and
framing
[1-2, ENTER='YES']:1
note: for the above you need to ask your provider
for the detaisl like crc4 is enable to disable based on that u need to
enter
Select clock for AFT-A101 on port 1 [slot:4 bus:4
span:1]
1. NORMAL
2. MASTER
[1-2]:2
Select signalling type for AFT-A101 on port 1
[slot:4 bus:4 span:1]
1. Zaptel/Dahdi - PRI CPE
2. Zaptel/Dahdi - PRI NET
3. Zaptel/Dahdi - E & M
4. Zaptel/Dahdi - E & M Wink
5. Zaptel/Dahdi - FXS - Loop Start
6. Zaptel/Dahdi - FXS - Ground Start
7. Zaptel/Dahdi - FXS - Kewl Start
8. Zaptel/Dahdi - FX0 - Loop Start
9. Zaptel/Dahdi - FX0 - Ground Start
10. Zaptel/Dahdi - FX0 - Kewl Start
11. Sangoma SMG/sangoma_prid- PRI CPE
12. Sangoma SMG/sangoma_prid- PRI NET
[1-12]:1
note: if the line is from the provider select 1 ,
if you are connecting card to leagal epabx then give 2
Select switchtype for AFT-A101 on port
1
1. National ISDN 2
2. Nortel DMS100
3. AT&T 4ESS
4. Lucent 5ESS
5. EuroISDN
6. Old National ISDN 1
7. Q.SIG
[1-7]:1
Configuring port 1 on AFT-A101 as a full
E1
1. YES - Use all channels
2. NO - Configure for fractional
[1-2, ENTER='YES']:1
Select dialplan context for AFT-A101 on port
1
1. from-pstn
2. from-internal
3. Custom
[1-3]:1
incomming context
Input the group for this port
:0
Port 1 on AFT-A101 configuration
complete...
Press any key to continue:
T1/E1 card configuration complete.
Press any key to continue:
Configuration Complete! Please select
following:
1. YES - Continue
2. NO - Exit
[1-2]:1
Dahdi and Wanpipe configuration complete: choose
action
1. Save cfg: Restart Asterisk & Wanpipe
now
2. Save cfg: Restart Asterisk & Wanpipe
when convenient
3. Save cfg: Stop Asterisk & Wanpipe
now
4. Save cfg: Stop Asterisk & Wanpipe
when convenient
5. Save cfg: Save cfg only (Not
Recommanded!!!)
6. Do not save cfg: Exit
[1-6]:1
Would you like wanrouter to start on system
boot?
1. YES
2. NO
[1-2]:1
Would you like to execute 'dahdi_cfg' each time
wanrouter starts?
1. YES
2. NO
[1-2]:1
end of wanroute configuration
Now you need to check pri status ,
1. type dahdi_cfg -- this shows does the card
configured properly or not , shows the channels configured
2. go to asterisk cli
asterisk -vvvvr
dahdi show status
dahdi show channels
pri show spans
Verificando con el comando lspci podemos ver que se encuentra la tarjeta
sangoma.
Una vez configurado automaticamente asterisk
reconocera la tarjeta.
Usando el comando lsdahdi obtenemos:
Dentro del CLI tambien podemos revisar:
